FLOWCON S

• Single line pump station available with any of the BS range of controllers
• Wilo ST 7m head pump available at extra cost
• Dial pressure gauge
• 3 or 6 bar pressure relief valve
• Flowmeter
• Fitted with manual air vent
• Filling and flushing unit
• Wall mounting kit
• Insulated casing
  

FLOWCON A

• Single line pump station that can be supplied with the AX controller or any of the BS range.
• Wilo ST 7m head pump available at extra cost
• Dial pressure gauge
• 3 or 6 bar pressure relief valve
• Flowmeter
• Filling and flushing unit
• Wall mounting kit
• Insulated casing

FLOWCON B, BS, BSL

• Twin line pump station that can be supplied without a controller or with any of the BS range of controllers.
• Wilo ST 7m head pump available at extra cost
• Flow and return thermometers
• Dial pressure gauge
• 3 or 6 bar pressure relief valves
• Flowmeter
• Filling and flushing unit.
• Manual air vent available at extra cost
• Wall mounting kit
• Insulated casing

FLOWCON RF

• Single return line pump station without controller.
• 7 & 8m head pumps available at extra cost
• Dial thermometer
• 3 or 6 bar pressure relief valve
• Flowmeter
• Filling and flushing unit
• Wall mounting kit
• Insulated casing

FLOWCON S2F

• Three line pump station for systems with 2 stores. Supplied without controller.
• 7 & 8 m head pumps available at extra cost
• Flow and return thermometers
• Dial pressure gauge
• 3 or 6 bar pressure relief valves
• Flowmeter
• Filling and flushing unit
• Wall mounting kit
• Insulated casing

FLOWCON D2F

• Three line pump station for systems with east/west collectors. Supplied without controller
• Specification as S2F

FLOWCON D

• Twin line pump station incl. DeltaSol D controller
• Ultra-fast and precise digital sensors measuring pressure, temperature and flow rate
• Flow and return thermometers
• 6 bar PRV with manometer
• Integrated air-stop, isolation and check valves
• Built in 'leakage' and 'over pressure' safety controls that shut the system down if the pressure is too low (<0.7 bar) or high (>5.5 bar). Both these parameters are user adjustable
• New controller display that can show system status, measured values and balanced values. Please click here for examples of this

Please note this pump station does not come with an integrated filling and flushing loop. These should be purchased separately. Please click here for order numbers and available sizes.

FLOWCON MAX

• Twin line pump station that can be supplied with or without air scoop and flowmeter
• 6, 7 and 12 meter pumps are available
• Flow and return thermometers
• 1" pump connections
• Dial pressure gauge
• 3 or 6 bar pressure relief valves
• Flowmeter
• Filling and flushing unit.
• Wall mounting kit
• Insulated casing

FLOWCON XL

• Twin line pump station for large solar arrays
• 1 1/4" internal thread connections
• 6, 7, 8 and 10 meter pumps are available
• Flow and return thermometers
• For collector areas up to 100m2 (@ 0.5 l/m2)
• Dial pressure gauge
• 6 bar pressure relief valve
• Fill and flush comissioning valves
• Wall mounting kit with intergrated check valves
• Insulated casing

SOLEX

• Pre-assembled heat exchange module.
• Integrated controller
• Available in 4 sizes for collector arrays of up to 50sq metres

SOLEX CASCADE

• Pre assembled heat exchange module for large systems
• Integrated controller
• Available in 4 sizes for collector arrays up to 250 sq metres

Please click here for more information on the Solex Cascade

FRIWA

The Friwa fresh water module allows mains water to be heated from a buffer tank through a large plate heat exchanger. The buffer can be heated from various sources such as solar, oil/gas boiler & solid fuel. This means their is no chance of bacteria being present in the potable water.

For larger systems mutiple Friwa modules can be linked.